A summary of  weaknesses in many so called “RIFE Machines”..

Please understand  to the best of our current knowledge NO ONE makes & sells
“Original Rife” equipment or machines  contrary to the many claims being made.

•        Complicated and confusing to program & use
•        Keyboard works poorly- hard to press, double entries
•        Many have software and hardware problems
•        No way to re-run a program unless stored to memory
•        Time not programmable into program
•        Poor electrical performance
•        Problems with multiple run frequencies
•        Poor Square wave waveform resulting in bad harmonic performance
•        Unbalanced output resulting in un-symmetrical delivered power

The premise of many so called “ RIFE” machines is their claim that they can directly generate the highest Rife
frequencies electrically through conduction rather than by means of a ray tube. Although they can generate the
frequencies conductively, their system does NOT deliver the same types of energies. Ray tubes deliver a broad
spectrum of energies, ranging from infrared, to electromagnetic fields, to electrostatic fields, to conductive electron flow
(plain old electricity), to light in the visible spectrum and beyond. The only energy most “Rife machines” deliver is plain
old electricity.

Although the manufacturers of “Rife type” devices attempt to argue otherwise, it is categorically true that “Skin Effect”
prevents high frequency electron flow (plain old electricity) from penetrating deeply into ANY electrically conductive
material. The higher the frequency, the shallower the penetration. At frequencies above 1MHz, skin effect will limit
penetration to a fraction of an inch.

A serious problem with many so called “ RIFE” machines is poor Square wave signal quality. A Square wave generates
a predictable series of odd order harmonic frequencies with an accurate energy balance. The closer the Square wave
is to perfect, the more accurate the harmonics are. Low Rise and fall time is the most difficult element to achieve in a
Square wave. A perfect Square wave has a rise time of zero, so the lower the rise and fall is, the better the Square
wave and thus the harmonics are.
BCX Ultra/BCX411:       150nsec from 1 to 100KHz, 1MHz, 1.25MHz, 1.67MHz

       About Custom Waveforms and Custom Modulation:
A fundamental difference between the BCX Ultra and most other Rife type devices is the way that they generate
waveforms. Many units use a DSP (digital synthesizing processor) which, by nature, is only capable of generating
Square waves. By using filtering techniques, the circuit is capable of approximate Sine wave ne wave by “rounding off
Square wave re wave. This is, of course, not particularly accurate, meaning that the purity of Sine wave is
compromised and most machines have NO sine waves..

The BCX Ultra uses entirely different electronics. It contains 3 separate Microprocessors each of which creates an
“Arbitrary Waveform”. Arbitrary Waveforms are exact and pure creations of natural occurring and incidental occurring
waveforms. Examples of  waveforms are Sin natural occurring e, Square, Triangle, Exponential, and Linear. An
example of an incidentally occurring waveform is the Hoyland Waveform. The BCX Ultra faithfully reproduces the
waveform that Hoyland generated using a complex array of apparatus. If fact, the Hoyland Waveform in the Ultra was
created by digitizing an actual copy of Hoyland’s test data. Another example of Arbitrary Waveforms are the Ultra’s Odd
Order Harmonic and Even Order Harmonics waveforms. The Odd Order Harmonic Waveform produces a fundamental,
and the 3’rd, 5’th, and 7’th harmonics is perfect harmonic proportion. The Even Order Harmonic Waveform produces a
fundamental, and the 2’nd, 4’th, and 6’th harmonics in perfect harmonic proportion.

With Arbitrary Waveforms, the Ultra can produce ANY waveform imaginable- accurately, and perfectly. Harmonics can
only be generated accurately and correctly if the fundamental waveform is accurate.
The BCX Ultra contains 3 Arbitrary Waveform generators, which when combined together
can produce an un-imaginable combination.
     
BIO ELECTRICS for HEALTH.com    1-800-936-6240

Please note This product and or information is for research purposes only and is not intended to prevent, diagnose,
treat or cure any disease.

The advanced BCX ULTRA
RIFE TYPE RADIO FREQUENCY TECHNOLOGY AT IT'S FINEST
BIO ELECTRICS for HEALTH.com       1-800-936-6240
Shift your frequency   Transform your life
         
        
 The NEW BCX ULTRA is truly amazing, with its
*** 1236 Preprogrammed channels for many common conditions
*** 256 channels to program with your own frequencies.
*** Frequency plasma tubes with a range up to 100,000 Hz.
*** Electrode delivery with a range up to 4,000,000 Hz,   
*** An exciting range of Wave forms…square, sine, triangle
and more to assist with the most advanced research
         Retail now only   $2695.00
Special Package free shipping and free consultation
call for details  800-936-6240  or    Email us
Judy has developed an EXCLUSIVE frequency service with special frequency  
sets and offers the Very best in assistance and customer support
.
Testimonials       WHY THE BCX ULTRA IS ONE OF THE BEST CHOICES IN
FREQUENCY TECHNOLOGY
                    
 http://rifefrequencysuccess.info/home
Does anyone sell a Rife unit like
   Royal Rife used in his lab?  
               No!*!*       


Hello D     You asked me to provide some sort of feedback on the machine. Here it is. You can use this letter for
whatever use you wish, either in it's entirety or portions. I don't mind my email being published.

My name is John White. I am an electrical engineer with 30 years experience in electronics and high power circuitry. I
have a technical background and don’t have a blind belief in alternative healing. I wish to give feedback of a
BCX-Ultra I purchased in May 2010. I have no commercial interest in this machine,
and the following is totally unbiased and honest.
Before purchasing the BCX-Ultra I investigated all the alleged "Rife" machines available on the market. I have also
designed and built Rife machines myself using advanced electronics, and measured the results obtained.
One must understand certain principles before deciding on the unit to buy. I will avoid technical terms to clarify to a
broader audience the points I am making.
A magical “resonant frequency” for cell destruction does not exist. Most Rife machine suppliers talk about cell
"resonance". An analogy often used is the wine glass cliché, where a certain frequency will shatter the glass. Take a
minute to think this one out. We are mostly composed of water. Fill a wine glass with water and it will never resonate.
No frequency will get the glass to break. What must be achieved is impedance resonance, which is very technical
and difficult to explain in layman’s terms.
Power levels are NOT important. In Royal Rife’s experiments, a greater effect was found when the power level was
lower.
What IS important is the transfer of energy from the frequency generator to the pathogen. This is achieved when the
radiation of the Rife machine matches that of the pathogen. This is known as impedance matching.

I evaluated all of the commercially available “Rife” units and believe the BCX-Ultra is the ONLY commercial unit on
the market today that will function correctly.
I am very impressed with the quality of the workmanship put into the BCX-Ultra. I have tested its output levels and
waveforms, and they are stable and accurate. The design engineers have obviously put an immense effort into
designing a world-class machine, and should be proud of what they have built.
I will illustrate the effectiveness of the BCX ultra with the following 4 examples.
My daughters had typical teenager acne, predominantly over her nose and forehead area. After only 1 session (45
minute standard program) the acne disappears *completely* over the subsequent 2 days. The program needs to be
repeated every 3 weeks. She holds the ray tubes across her cheeks as she watches TV. No cream product works as
well and instantly as the BCX-Ultra.

My wife became struck with the “flu”. She was so severely hit that she crawled into bed with a fever, shivering and
with aching joints, and was unable to move. I pried open her fingers and ran a virus program with her holding the ray
tubes. She fell asleep, and I left her. After an hour she came into the kitchen complaining she was hungry. The
program had completed, she had no fever, and she was cured. I quite simply could not believe my eyes.

I treated a friend with extremely evasive small cell cancer. The cancer had grown from her lungs into her lymphatic
system. I treated her before she began chemotherapy, and the size of her tumour reduced remarkably after just 2
sessions. The chemotherapy has now poisoned her to the stage that she has been too unwell for further “Rife”
treatment.
Last night I had a sore throat, running nose and felt very unwell. I ran the same program with the tubes across my
throat. An hour after the program completed my sore throat was gone. 8 hours later my energy levels have returned.
Normally when I get a sore throat I feel unwell for at least a week. This has prompted me to finally send feedback on
the machine
If you are looking at purchasing a “Rife” machine that will not disappoint, you need to buy this unit. It is very
aggressive and precise, and you will get remarkable results. Remember it is not a toy, and you will feel tired after
treatment as your body flushes out the dead pathogens. I would recommend you predominantly use the hand held
ray tubes as they will give better results.
I find myself unable to fault the BCX-Ultra. It will kill outright many, if not all, pathogens, often with complete cures
after a single session. Remember to drink plenty of fluids so your body can eliminate the waste.
In future models I would like to see the option of selecting higher definable carrier frequencies, computer control via
USB, and bio feedback.
In summary, I am exceedingly pleased in my purchase decision. If you have a medical condition or want to prevent
future illnesses, get a BCX-Ultra for yourself, and give those bacteria / virii the roasting they deserve.
***********************************************************************************************************************
************************************************************************************************************************************

======================================================================================
============================================

Buyers Guide to Rife Generators


Does anyone sell a Rife unit like Royal Rife used in his lab? No. His unit would flash for milliseconds to ½
minute and kill whatever specimen he had in the field. His machine could be detected miles away. There
is no way the FTC would allow a machine like this in our modern day world with that much power.

In the 20+ years we have dealt with Rife equipment many people have said, “We have the only true Rife
machine.” It is all a pack of lies. There is no such animal.

The Hoyland machine came along after Rife built his unit. Hoyland used RF (radio frequency) as Rife did.
Hoyland worked in the meg range (millions). Hoyland’s unit was actually very successful. Some say that
Hoyland used Rife’s microscope to find the MOR (mortal oscillatory rates). We also know Hoyland copied
some of Rife’s Frequencies. Some say that Hoyland got all his frequencies from Rife

Here is a list of important features to look for in a frequency unit before you purchase one.


1. The most important feature to look for is a unit using a RF carrier. Rife used RF, Hoyland used RF and
this was a big part of their success. The reason is very simple: the audio frequency range that you find
listed in the frequency manual that comes with your machine is carried much better with a frequency in a
higher frequency range than the audio frequency you are running. We use a high audio frequency to
carry the audio frequency that you are experimenting with .The only way you can hear a radio wave
(voice) in a brick building in the next town over is the use of RF, because the RF carries the audio. We
also know the only way to get deep penetration in the body is with a unit that has a RF carrier frequency
built in. Most units on the market today don’t use RF.

2. It is very important that the unit you choose has ray tubes. Royal R. Rife used ray tubes and so did
Hoyland. Find a unit that has hand held ray tubes because they complete the circuit by running through
the body between the hand held tubes thus guaranteeing that the frequencies flow through the body.
The ray tubes produce a much higher voltage than pad devices to push the frequencies deeper into the
body. There is the magnetic effect  produced by gas filled tubes (that can be tested) that especially used
with RF penetrates deeply into the body. Most people prefer the “soft” “energetic” “warm” feel of the
glass tubes compared to the electrical tingle felt from the metal electrodes. Many people report that
watching and feeling the glass tubes “glow and flow’ has a relaxing, calming, softening effect on their
body.

Ray tubes deliver a broad spectrum of energies, ranging from infrared, to electromagnetic fields, to
electrostatic fields, to conductible electron flow (plain old electricity), to light in the visible spectrum
and beyond. The only energy pad devices deliver is plain old electricity.

3. A unit that comes with light emitting diodes (LEDs) is a very good feature. Many good results to your
health can be attained by using LEDs, such as better eye sight and clearing up many skin conditions.
Faster healing from the LED’s and the healing effects from the Rife frequencies combine as a powerful,
effective tool.

4. There can certainly be an advantage to a unit that can do the feet and hands at the same time. Many
units will come only with hand cylinders, which are good for dealing with an upper body cold. However,
someone with circulation problems in the feet and legs would greatly benefit from using a unit with both
hand and foot electrodes.

5. People call us up and inquire about a unit that may be in the $500 range and why does yours cost so
much more? Twenty two years ago when we started in this business by selling the Scalar Tronix
machine, the units sold then were modified function generators off the shelf, which are mass-produced.
Rife machine manufacturers generally build a relatively small number of machines so the cost goes up
enormously. A function generator is low powered. It will cost more money to build a circuit that has the
power required in a Rife machine. Another added cost is crystal control that makes the price go up.
Crystal control greatly adds to the accuracy of a frequency that is needed in a Rife unit. An example
would be 9.7 Hz for tendons. You don’t want 9.6 or 9.8 because your results will be diminished. Another
example, 1444Hz is to normalize testosterone in men and 1445 is to normalize testosterone in women.
You certainly wouldn’t want a male using the machine and have the frequency drift up towards
1445.           

By the time you add foot plates, hand cylinders, reusable electrodes (sticky patches), and LEDs, you
certainly add to the cost of an off the shelf function generator

6. Make sure you purchase a machine that actually reads out in Hz. New frequencies come out all the
time and you want to have the capability to add these new numbers as they come out.


7. It is important to purchase a unit that has duty cycle and gating. Rife and Hoyland used gating and duty
cycle because they knew it made their units more effective.

8. We could have produced a unit with 12 frequencies running simultaneously as a sales gimmick. We
didn’t do that for the following reason: In the 22 (17 in manufacturing our own frequency units) years we
have dealt with Rife technology, we have found that more power worked better. Here is exactly what is
happening with say running 6 frequencies simultaneously. Suddenly you have 1/6th the power per
frequency that you had when running only 1 frequency at a time. Theoretically, to get the same exposure
per frequency you would need to run the program 6 times longer. However, in practice we have found
that you need more power to penetrate deep into the body. Therefore, from our experience we have
found that the weaker the frequency the more units of electricity you need to destroy microbes. Simply
put, you would need to stay on the frequency unit longer doing the 6 frequencies than using 1
frequency at a time.



We are going to toot our own horn here. But as you go through the document enclosed, I think you will
see why wanting to build the best unit out there, we did what we did.

Our unit does have RF, gating, duty cycle, footplates, hand cylinders, reusable electrodes, LEDs, crystal
control, and plenty of power. We use hand held glass tubes to conduct the RF frequency and audio
range frequency into the body. Our engineers came up with the idea that with conductors (that is
completing the circuit when you hold both glass tubes) you are guaranteeing completing the circuit
through your body. We probably know better than anyone else why RF works better than just using the
audio frequencies because for the first 2 years we had only the audio. We only had the BioTec 2000.
When we added the BioTec 2000 Ray tube unit our results went up through the roof (we renamed our
units the BCX211 and BCX411). Yes, we had a good comparison because we had a lot of people calling
us with their results using the RF and also just the audio. Our latest unit is called the BCX Ultra.

Many people ask us, “How do you know which machine to buy? There are so many and they all say they
have the original Rife machine.” We tell people, “It is simple, just study the features that Rife and
Hoyland used and buy a machine that has the most features that their machines had.”


October 19, 2009 6:07 PM
Subject: BCX Ultra Service

Hi, Roger and Judy,
As you may recall, I purchased three (3) BCX Ultras, one for myself,
one for my brother, and one for my father. I’ve witnessed tremendous
BCX-related health benefits not only in my own family members, but
also in my Lyme disease patients at Envita Medical Center . I’ve
incorporated the BCX Ultra into our comprehensive Lyme disease
treatment protocol, which typically involves intravenous and oral
antibiotics for six weeks or more. In my estimation, the BCX Ultra
(used privately at home, of course) is critical to eradicating Lyme
disease after patients have completed the extensive IV and oral
antibiotic regimen. It’s really quite amazing and, at the same time,
gratifying. I routinely have patients inform me how much better they
feel after extended private use of the BCX Ultra at home. However, I
do wish that I could duplicate these same successes in our cancer
patients, many of whom are quite advanced (stage IV).

My brother has been using the BCX Ultra for Lyme disease and chronic
fatigue syndrome virtually every other day for almost seven months
with marked improvement. Clinically, I would estimate that his
overall improvement is approximately 60%, which is remarkable, given
the fact that he has had chronic fatigue syndrome and probable Lyme
disease for almost ten years. ?

Thanks very much,

Brent Korn

Brent Robert Korn, D.O.
Envita Medical Center
Scottsdale, Arizona

********************************************************************************************************************************************
*****************************************************************************************************************************************************
Judy is a gifted  intuitive
and  researcher
for intuitive  consultation
to assist you in getting   
the BEST frequency for  
you issues
click here  
or email judy
Dear Judy,
This letter is to state my appreciation for all you have done.  As you know, I purchased newer
gas tubes and the Vortex from you.  Despite me not purchasing the BCX Ultra from you, I am
grateful that you were willing to answer my questions and provide me with the necessary
support services not offered from my original supplier.  

Your support was far more than I expected.  Furthermore, when the published frequencies
were not working you were able to intuitively provide me with the frequencies that immediately
worked.

Your intuitive talents and patient customer services are truly precious gifts.   May you live long
and prosper.  

Thank you,
Dr. A. Tenzar       Chicago
--------------------------------------------------------------------------------------------------------------------
Sent: Mon, June 6, 2011 11:08:25 PM

Hi back Judy, I’m so glad I made the right choice of machines. Your knowledge, experience and
assistance made my wife and I feel great on our choice. Wish I had made the right decision
sooner. Thanks for the link, I am going to send it to my Lyme friends suffering on antibiotics.
Also to my NP Dr. here in Olympia, that I will see on Wed. for the first time since my treatment in
AZ.

Thanks So Much,
Dan & Georgia
-----------------------------------------------------------------------------------------------------------------------------------
Sent: Wednesday, August 10, 2011 6:15 AM
To all concerned:
When you purchase a product, your satisfaction depends on the sound research and support
available to you. The Ultra line of products distributor,Judy Erwin, of Bioelectrics is very
knowledgeable and helpful in getting the customer off to a great start. She is there when you
need help! Her advice helped me advance my skills and use of the products.
Thank you Judy!!
Buzz
PS... Buzz has been a client for over 5yrs now
--------------------------------------------------------------------------------------
Subject: Re: PS Re: Judy Question

Thanks for the info.  I REALLY appreciate your feedback and help.  
Take care,
Cary
Jim Marrs.com
Unorthodox yet effective radio
frequency technology, pioneered
by Royal Raymond Rife in the
early 20th century, has slowly
been breaking the choke hold of
the monolithic corporate drug
industry. Frequency technology
often can provide a noninvasive,
safe and effective alternative to
drugs, chemicals and surgery. I
know this from personal
experience over a period of more
than 15 years. The use of
frequencies literally has saved
me thousands of dollars in
medical bills and
pharmaceuticals. And no one
understands the uses and
successes of this technology
better than Judy Erwin, who has
fought a lifelong battle against a
variety of medical maladies.
Jim Marrs, Author of four New
York Times Best Sellers on
government and corporate
conspiracies.